SS 525HF
Installation Guide
Click Image above for High Resolution Diagram
| LAND ROVER COUNTY V8 V8 PETROL (3.5L) CARBURETOR MODELS | |
| Fitment to: Right hand side
Fitting time: Approximately 110 minutes Special Tools:
|
|
| 1 | Remove:
|
| 2 | Tape the template in position on the upper rear corner of the right hand guard. Mark the hole positions using a felt pen. After applying several layers of tape to protect the paintwork, cut the main hole using an air hacksaw. Drill the mounting holes to 16mm using a stepdrill. |
| 3 | Trim 45mm off the snorkel snout. Screw the 3 stainless steel studs into the back of the snorkel. Bolt the upper mounting bracket to the snorkel body. Sit the snorkel in position on the vehicle and mark the upper mounting holes on the windscreen frame. Remove the snorkel from the vehicle and drill the upper holes to 3.5mm. |
| 4 | Run ducting from the hole in the guard, under the brake master cylinder then towards the air cleaner inlet. |
| 5 | Use a small bead of silicone to adhere the body gasket to the back of the snorkel body. The same technique should be used to join the upper mounting bracket to the bracket gasket. |
| 6 | Clamp the ducting to the snorkel snout, then fasten the snorkel to the vehicle using appropriate hardware. Refit the guard support bracket and the vacuum reservoir. |
| 7 | Remove the air cleaner assembly. Remove the baffle from the end of the air cleaner snout and the locating pin from the underside of the air cleaner body. Slide the reducer onto the air cleaner snout as far as possible. Secure in position using four 4mm pop rivets. Seal the join thoroughly with silicone. |
| 8 | Refit the air cleaner assembly. Clamp the ducting to the small end of the reducer. Using cable ties, tie down the ducting to prevent any rubbing. |
| 9 | Fit the air ram to the top of the snorkel. Remove the 90o bracket from the bonnet frame as this may damage the snorkel ducting. |
| WARNING: IT IS THE INSTALLERS RESPONSIBILITY TO ENSURE ALL CONNECTIONS ARE WATER TIGHT. | |
|
ITEM
|
IMAGE
|
DESCRIPTION
|
QTY
|
PART NO.
|
| 1 |
 |
BODY SNORKEL | 1 | 810-133-200 |
| 2 |
 |
3 ½"AIR RAM - Assembly | 1 | 000-135-650 |
| 3 |
 |
BRACKET - Upper - Mounting | 1 | 810-032-000 |
| 4 |
 |
GASKET | 1 | 810-435-000 |
| 5 |
 |
BOLT - Hex - 6mm x 1.0 x 14mm | 3 | 000-002-100 |
| 6 |
 |
STUD - 8mm x 1.25 x 25mm - O/L | 3 | 000-110 |
| 7 |
 |
WASHER - Body - 8mm x 30mm | 3 | 000-311 |
| 8 |
 |
NUT - Nyloc - 8mm x 1.25 | 3 | 000-205 |
| 9 |
 |
SCREW - S/T - 4.2mm x 13mm | 5 | 000-951 |
| 10 |
 |
RIVET - Pop - 4mm | 4 | 000-958 |
| 11 |
 |
CLAMP - Hose - 60 / 80mm - Silver | 2 | 000-907 |
| 12 |
 |
TIE STRAP - Nylon - 7.8 x 365mm | 4 | 000-987-365 |
| 13 |
 |
DUCTING - RFH - 3" x 1400mm | 1.4M | 000-885-140 |
| 14 |
 |
REDUCER - 4" / 3" | 1 | 810-025-200 |
| 15 |
 |
GASKET - Foam Body | 1 | 810-016-200 |
| 16 |
 |
TEMPLATE | 1 | 810-017-200 |
| 17 |
 |
HOSE CLAMP - SIZE 56 (BLACK) | 1 | 000-914/B |