SS 73HF
Installation Guide
Click Image above for High Resolution Diagram
| TOYOTA LANDCRUISER BJ 73 3B DIESEL (3.4L) 13BT TURBO DIESEL (3.4L) | |
| Fitment to: Right hand side Fitting time: Approximately 110 minutes Special Tools:
|
|
| 1 | Remove:
|
| 2 | Tape the template in position on the vehicle (refer to the drawing) and mark all the hole positions using a felt pen. Remove the template. |
| 3 | Drill a 4mm pilot hole for each of the holes. Open out the 4 mounting holes to 16mm using a step drill. Using an 89mm holesaw, cut the main hole. The drill should be held at 90 deg to the panel while cutting this hole. After drilling/cutting, deburr each hole to leave a clean edge. |
| 4 | Screw the stainless steel studs into the inserts in the back of the snorkel. Fasten the upper mounting bracket to the snorkel using two 6mm bolts and washers. Locate the snorkel on the vehicle and mark the upper mounting holes on the "A" pillar using a felt pen. Remove the snorkel and drill the mounting holes to 8mm. |
| 5 | Paint all holes to prevent rust. Insert the plastic body clips into the upper mounting holes. Position the snorkel on the vehicle and secure using appropriate hardware. |
| 6 | Remove the air cleaner snout from the air cleaner by drilling out the spot welds. A sharp chisel will be needed to carefully separate the snout from the main air cleaner body. Remove the deflector from inside the air cleaner also. Slide the adapter casting onto the snorkel snout. Place the air cleaner in position and mark the casting location on the air cleaner body. Remove the air cleaner and casting from the car. Locate the casting on the air cleaner body and via the adapter snout and mark the internal hole location. Remove the adapter and using an air hacksaw, cut the new inlet hole to match the casting. Rivet the casting into position on the air cleaner body and seal the joint with silicone. |
| 7 | Place a bead of silicone around the adapter snout and refit the air cleaner to the vehicle. |
| 8 | Sit the air ram on top of the snorkel and secure it using the clamp supplied. |
| * | A small bead of silicone may be placed around the top and front edges of the snorkel to seal it against the vehicle. |
| WARNING: IT IS THE INSTALLERS RESPONSIBILITY TO ENSURE ALL CONNECTIONS ARE WATER TIGHT. | |
|
ITEM
|
IMAGE
|
DESCRIPTION
|
QTY
|
PART NO.
|
| 1 |
 |
SNORKEL BODY | 1 | 330-133-000 |
| 2 |
 |
3" AIR RAM ASSEMBLY | 1 | 000-135-050 |
| 3 |
 |
STUD - S/S - 8mm1.25 x25mm O/L | 4 | 000-110 |
| 4 |
 |
WASHER - BODY - 8mm x 30mm | 4 | 000-311 |
| 5 |
 |
NUT - NYLOC - 8mm1.25 | 4 | 000-205 |
| 6 |
 |
BRACKET - UPPER MOUNTING | 1 | 330-032-000 |
| 8 |
 |
BOLT - HEX - 6mm x 1.0 x 14mm | 2 | 000-001 |
| 9 |
 |
CLIP - BODY - PLASTIC | 3 | 000-960 |
| 10 |
 |
SCREW - S/T - 4.2 x13mm | 3 | 000-951 |
| 11 |
 |
ADAPTOR - AIR CLEANER | 1 | 330-023-000 |
| 12 |
Included in Item 11
|
"O" RING - 5/16" SECTION x 290mm | 1 | 000-470-029 |
| 13 |
 |
POP RIVET - 4mm x 12mm | 6 | 000-958 |
| 14 |
 |
TEMPLATE | 1 | 330-017-200 |
| 15 |
 |
PLUG - PLASTIC - 70mm | 1 | 000-959-200 |
| 16 |
 |
CLAMP - HOSE - 60/80 | 1 | 000-907 |
| 17 |
 |
HOSE CLAMP - SIZE 48 (BLACK) | 1 | 000-918/B |